Construction Technology

 
 

Construction technology: Frame-panel

 

Frame and panel wall from «Promstroyles»

 

Frame-and-panel wall with exposed log wall

  1. On the street side of glued beam can have different thickness, height and shape.
  2. The entire frame structure of the walls is 100% from glued beams.
  3. Due to the frame structure from the walls excluded the sheets of OSB.
  4. At the construction site do the wall up to a length of 9 m, painted, installed Windows, frames, reveals and sills.
  5. Interior wood trim is 100% factory installed.
  6. Design of external walls General requirements on thermal insulation of houses for permanent residence.

 

  • Frame and panel walls: exterior finish - laminated timber
     
    1. SET OF DOCUMENTS
    1. Installation drawings;
    2. Bill of materials;
     
    2. BOTTOM RAIL
    1. Capillary waterproofing under bearing walls (izoplast);
    2. Impregnated backing Board
     
    3. The EXTERIOR WALLS of the 1st floor
    1. Glued beam;
    2. Windscreen vent;
    3. Glued frame;
    4. Heater «Roсwool» 200 mm; density 35-40
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    4. INTERIOR WALLS
    1. Glued frame;
    2. Heater «Roсwool» 100 mm; density 35-40;
    3. Finish simulator timber - 50% of the surfaces or GCR.
     
    5. BACKBOARD FLOOR
    1. Main glued beams (project);
    2. Glued the frame of the secondary beams;
    3. The ventilation membrane ceiling;
    4. Noise insulation «Roсwool» 100 mm; density 35-40;
    5. OSB 15 mm;
    6. Bar 40 х 40 mm;
    7. Finishing floors - decking 40 mm;
    8. Option: laminated plate PSL 60-200 mm.
    9. Option: silent ceiling
     
    6. The EXTERIOR WALLS of the 2nd floor
    1. Glued beam;
    2. Windscreen vent;
    3. Glued frame;
    4. Heater «Roсwool» 200 mm; density 35-40
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    7. ROOFING
    1. Truss legs (option: laminated plate PSL);
    2. Glued ridged, secondary beams, based on the characteristics of the project;
    3. Heater «Roсwool» 200 mm (option 300 mm); density 35;
    4. Vapor barrier (membrane);
    5. Windscreen (membrane);
    6. Bar change of direction (Board sheathing finished ceiling);
    7. Board finishing gypsum Board or ceiling;
    8. Crate (Board for the organization of the air gap of the roof);
    9. Planed counter lathing with prorezheniye technical conditions of roofing tiles (Board to install tile roofing (except shingles) and the side ventilation of the roof.
     
    8. CEILINGS
    Finishing ceilings - ceiling Board 18 mm (spruce, pine) or GCR.
     
    9. WOODEN WINDOWS from glued beams, the German technology
    Windows are rectangular with double seal, aluminium drip cap, door thickness 82 mm, single color in color in color (a painting system "SIKKENS"), glass (36 mm) - M1 double chamber glass thickness.4 mm, opening Windows - tilt and turn (1-fold for the opening), accessories "ROTO NT".
    Windows oblique, round, stained-glass area of more than 3M. square, arched and Windows are less than 1 m2 - oplachivaetsya is a difficulty.
    Bars, rastekanie sash-bars, mosquito nets, coloured in two colors,shutters, blinds, armored and colored glass are extra.
     
    10. DOOR
    The interior is paneled from solid knotty pine, clear lacquer, manufacture Finland or Russia. Leaf height up to 2000 mm., width of 600-900 mm., the Furniture production in Finland.
    Front door (1 piece) - insulated, painted with the "SIKKENS" system, the glass - on request.
     
    11. MOLDED PRODUCTS
    Baseboard, fillet, trim, window sills, layout, overhangs, windshields, windshield, cornice boards, sills, block, Board terrace, terrace fence, slab, terrace garden design, design of roof, beams, rafters, and any other individual wooden elements related to the concept of a wooden house, unconstructive in addition to decorative beams, wood carving, figure connecting.
     
    12. STAIRS
    Ladder made of pine (knots allowed) on the string with a turn at 90º or 180º, platform, or winder treads (according to architecture), lifting height more than 3M, width of steps between 750-1000 mm, without podstupenej, with fencing on the inner side, the wall of the opening steps, finish - clear lacquer, work on ladders to install. Section details:
    1) the string (thickness 45 mm, width - calculation)
    2) level (thickness 45mm, width not over 300 mm)
    3) area (thickness 45mm, width not exceeding 900 mm)
    4) handrails (thickness 45 mm, height 80 mm)
    5) supporting pillars of staircases, pillars, fences (78х78 mm)
    6) baluster rectangular (35х30 mm)
    7) fence opening (length 1000 mm 1.5 column)
    Paid in addition: Replacement of the string to the stringer, stair risers, finishing of end stage birch panel, stairs from the valuable breeds of wood,tinted, invitations (radial) steps, handrails (fences) on the outer side of the staircase,replacement of balusters,the railing of the second light and install it.
     
    13. ANTISEPTIC OF WALL MATERIAL
    The base layer of antiseptic (Finland);
     
    14. COMPONENTS
    All the fixings are metal products (nails, clips, bolts, hangers, straps, plates, etc.), except the metal beams
     

Panel timber frame wall with exterior cladding (brick, plaster)

  1. Outer simulator timber may have a different height and thickness.
  2. The maximum possible simulation — a log with a diameter of 29 cm
  3. The entire frame structure of the walls is 100% from glued beams.
  4. Due to the frame structure from the walls excluded the sheets of OSB.
  5. At the construction site do the wall up to a length of 9 m, painted, installed Windows, frames, reveals and sills.
  6. Interior wood trim is 100% factory installed.
  7. Design of external walls General requirements on thermal insulation of houses for permanent residence.

 

  • Specification full kit at home.
    Frame and panel walls: exterior finish facing brick or decorative plaster.
     
    1. THE SET OF DOCUMENTS
    1. Installation drawings;
    2. Specification of materials;
     
    2. THE BOTTOM RAIL
    1. Capillary waterproofing under bearing walls (izoplast);
    2. Impregnated with a Board backing
     
    3. The EXTERIOR WALLS of the 1st floor
    1. Facing brick. (made in Russia) or decorative plaster;
    2. OSB 10 mm;
    3. Windscreen vent;
    4. Glued frame;
    5. Insulation "Roсwool" 200 mm; density of 35-40;
    6. Vapor barrier channel for networking;
    7. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    4. INTERIOR WALLS
    1. Glued frame;
    2. Insulation "Roсwool" 100 mm; density of 35-40;
    3. Finish simulator timber - 50% of the surfaces or GCR.
     
    5. BACKBOARD FLOOR
    1. Main glued beams (project);
    2. Glued the frame of the secondary beams;
    3. The ventilation membrane overlap;
    4. Insulation "Roсwool" 100 mm; density of 35-40;
    5. OSB 15 mm;
    6. The bar 40 x 40 mm;
    7. Finishing floor - decking 40 mm;
    8. Option: laminated plate PSL 60-200 mm.
    9. Option: silent ceiling
     
    6. The EXTERIOR WALLS of the 2nd floor
    1. Facing brick. (made in Russia) or decorative plaster;
    2. OSB 10 mm;
    3. Windscreen vent;
    4. Glued frame;
    5. Insulation "Roсwool" 200 mm; density of 35-40
    6. Vapor barrier channel for networking;
    7. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    7. ROOFING
    1. Truss legs (option: laminated plate PSL);
    2. Glued ridged, secondary beams, based on the characteristics of the project;
    3. Insulation "Roсwool" 200 mm (optional 300 mm); density 35;
    4. The vapor barrier (membrane);
    5. Windscreen (membrane);
    6. Bar change of direction (Board sheathing finished ceiling);
    7. Board finishing gypsum Board or ceiling;
    8. Crate (Board for the organization of the air gap of the roof);
    9. Planed counter lathing with prorezheniye technical conditions of roofing tiles (Board to install tile roofing (except shingles) and the side ventilation of the roof.
     
    8. CEILINGS
    Finishing ceilings - ceiling Board 18 mm (spruce, pine) or GCR.
     
    9. WOODEN WINDOWS from glued beams, the German technology
    Windows are rectangular with double seal, aluminium drip cap, door thickness 82 mm, painting in a single color on the color ha Miu (painting system "SIKKENS"), glass (36 mm) - M1 double chamber glass thickness.4 mm, opening Windows - tilt and turn (1-fold for the opening), accessories "ROTO NT".
    Windows oblique, round, stained-glass area of more than 3M. square, arched and Windows are less than 1 m2 - oplachivaetsya is a difficulty.
    Bars, rastekanie sash-bars, mosquito nets, coloured in two colors,shutters, blinds, armored and colored glass are extra.
     
    10. DOORS
    The interior is paneled from solid knotty pine, clear lacquer, manufacture Finland or Russia. Leaf height up to 2000 mm., width of 600-900 mm., the Furniture production in Finland.
    Front door (1 piece) - insulated, painted with the "SIKKENS" system, the glass - on request.
     
    11. MOLDED PRODUCTS
    Baseboard, fillet, trim, window sills, layout, overhangs, windshields, windshield, cornice boards, sills, block, Board terrace, terrace fence, slab, terrace garden design, design of roof, beams, rafters, and any other individual wooden elements related to the concept of a wooden house, unconstructive in addition to decorative beams, wood carving, figure connecting.
     
    12. STAIRCASE
    Ladder made of pine (knots allowed) on the string with a turn at 90º or 180º, platform, or winder treads (according to architecture), lifting height more than 3M, width of steps between 750-1000 mm, without podstupenej, with fencing on the inner side, the wall of the opening steps, finish - clear lacquer, work on ladders to install. Section details:
    1) the string (thickness 45 mm, width - calculation)
    2) level (thickness 45mm, width not over 300 mm)
    3) area (thickness 45mm, width not exceeding 900 mm)
    4) handrails (thickness 45 mm, height 80 mm)
    5) supporting pillars of staircases, pillars, fences (78х78 mm)
    6) baluster rectangular (35х30 mm)
    7) fence opening (length 1000 mm 1.5 column)
    Paid in addition: Replacement of the string to the stringer, stair risers, finishing of end stage birch panel, stairs from the valuable breeds of wood,tinted, invitations (radial) steps, handrails (fences) on the outer side of the staircase,replacement of balusters,the railing of the second light and install it.
     
    13. ANTISEPTIC OF WALL MATERIAL
    The base layer of antiseptic (Finland);
     
    14. COMPONENTS
    All the fixings are metal products (nails, clips, bolts, hangers, straps, plates, etc.), except the metal beams
     

Panel timber frame wall with exterior siding simulator lumber

  1. Outer simulator timber may have a different height, thickness, roughness, depth and profile of the chamfer (American, Scottish, Scandinavian and traditional).
  2. Corner joints can be performed by cutting of laminated veneer lumber, which creates a 100% imitation of a house made entirely of laminated veneer lumber.
  3. The entire frame structure of the walls is 100% from glued beams.
  4. Due to the frame structure from the walls excluded the sheets of OSB.
  5. At the construction site do the wall up to a length of 9 m, painted, installed Windows, frames, reveals and sills.
  6. Interior wood trim is 100% factory installed.
  7. Design of external walls General requirements on thermal insulation of houses for permanent residence.

 

  • Specification full kit at home.
    Frame and panel walls: exterior finish simulator timber.
     
    1. THE SET OF DOCUMENTS
    1. Installation drawings;
    2. Specification of materials;
     
    2. THE BOTTOM RAIL
    1. Capillary waterproofing under bearing walls (izoplast);
    2. Impregnated with a Board backing
     
    3. The EXTERIOR WALLS of the 1st floor
    1. Glued laminated timber (semi-log 80 mm);
    2. Windscreen vent;
    3. Glued frame;
    4. Insulation "Roсwool" 200 mm; density of 35-40;
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    4. INTERIOR WALLS
    1. Glued frame;
    2. Insulation "Roсwool" 100 mm; density of 35-40;
    3. Finish simulator timber - 50% of the surfaces or GCR.
     
    5. BACKBOARD FLOOR
    1. Main glued beams (project);
    2. The ventilation membrane overlap;
    3. The ventilation membrane overlap;
    4. Insulation "Roсwool" 100 mm; density of 35-40;
    5. OSB 15 mm;
    6. The bar 40 x 40 mm;
    7. Finishing floor - decking 40 mm;
    8. Option: laminated plate PSL 60-200 mm.
    9. Option: silent ceiling
     
    6. The EXTERIOR WALLS of the 2nd floor
    1. Simulator timber (logs);
    2. Windscreen vent;
    3. Glued frame;
    4. Insulation "Roсwool" 200 mm; density of 35-40
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    7. ROOFING
    1. Truss legs (option: PSL beams-plate);
    2. Glued ridged, secondary beams, based on the characteristics of the project;
    3. Insulation "Roсwool" 200 mm (optional 300 mm); density 35;
    4. The vapor barrier (membrane);
    5. Windscreen (membrane);
    6. Bar change of direction (Board sheathing finished ceiling);
    7. Board finishing gypsum Board or ceiling;
    8. Crate (Board for the organization of the air gap of the roof);
    9. Planed counter lathing with prorezheniye technical conditions of roofing tiles (Board to install tile roofing (except shingles) and the side ventilation of the roof.
     
    8. CEILINGS
    Finishing ceilings - ceiling Board 18 mm (spruce, pine) or GCR.
     
    9. WOODEN WINDOWS from glued beams, the German technology
    Windows are rectangular with double seal, aluminium drip cap, door thickness 82 mm, painting in a single color on the color ha Miu (painting system "SIKKENS"), glass (36 mm) - M1 double chamber glass thickness.4 mm, opening Windows - tilt and turn (1-fold for the opening), accessories "ROTO NT".
    Windows oblique, round, stained-glass area of more than 3M. square, arched and Windows are less than 1 m2 - oplachivaetsya is a difficulty.
    Bars, rastekanie sash-bars, mosquito nets, coloured in two colors,shutters, blinds, armored and colored glass are extra.
     
    10. DOORS
    The interior is paneled from solid knotty pine, clear lacquer, manufacture Finland or Russia. Leaf height up to 2000 mm., width of 600-900 mm., the Furniture production in Finland.
    Front door (1 piece) - insulated, painted with the "SIKKENS" system, the glass - on request.
     
    11. MOLDED PRODUCTS
    Baseboard, fillet, trim, window sills, layout, overhangs, windshields, windshield, cornice boards, sills, block, Board terrace, terrace fence, slab, terrace garden design, design of roof, beams, rafters, and any other individual wooden elements related to the concept of a wooden house, unconstructive in addition to decorative beams, wood carving, figure connecting.
     
    12. STAIRS
    Ladder made of pine (knots allowed) on the string with a turn at 90º or 180º, platform, or winder treads (according to architecture), lifting height more than 3M, width of steps between 750-1000 mm, without podstupenej, with fencing on the inner side, the wall of the opening steps, finish - clear lacquer, work on ladders to install. Section details:
    1) the string (thickness 45 mm, width - calculation)
    2) level (thickness 45mm, width not over 300 mm)
    3) area (thickness 45mm, width not exceeding 900 mm)
    4) handrails (thickness 45 mm, height 80 mm)
    5) supporting pillars of staircases, pillars, fences (78х78 mm)
    6) baluster rectangular (35х30 mm)
    7) fence opening (length 1000 mm 1.5 column)
    Paid in addition: Replacement of the string to the stringer, stair risers, finishing of end stage birch panel, stairs from the valuable breeds of wood,tinted, invitations (radial) steps, handrails (fences) on the outer side of the staircase,replacement of balusters,the railing of the second light and install it.
     
    13. ANTISEPTIC OF WALL MATERIAL
    The base layer of antiseptic (Finland);
     
    14. COMPONENTS
    All the fixings are metal products (nails, clips, bolts, hangers, straps, plates, etc.), except the metal beams
     

Panel timber frame wall with exterior siding simulator logs

  1. Outer simulator timber may have a different height, thickness, roughness, depth and profile of the chamfer (American, Scottish, Scandinavian and traditional).
  2. Corner joints can be performed by cutting of laminated veneer lumber, which creates a 100% imitation of a house made entirely of laminated veneer lumber.
  3. The entire frame structure of the walls is 100% from glued beams.
  4. Due to the frame structure from the walls excluded the sheets of OSB.
  5. At the construction site do the wall up to a length of 9 m, painted, installed Windows, frames, reveals and sills.
  6. Interior wood trim is 100% factory installed.
  7. Design of external walls General requirements on thermal insulation of houses for permanent residence.

 

  • Specification full kit at home.
    Frame and panel walls: exterior finish simulator log.
     
    1. THE SET OF DOCUMENTS
    1. Installation drawings;
    2. Specification of materials;
     
    2. THE BOTTOM RAIL
    1. Capillary waterproofing under bearing walls (izoplast);
    2. Impregnated with a Board backing
     
    3. The EXTERIOR WALLS of the 1st floor
    1. The simulator logs;
    2. Windscreen vent;
    3. Glued frame;
    4. Insulation "Roсwool" 200 mm; density of 35-40;
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    4. INTERIOR WALLS
    1. Glued frame;
    2. Insulation "Roсwool" 100 mm; density of 35-40;
    3. Finish simulator timber - 50% of the surfaces or GCR.
     
    5. BACKBOARD FLOOR
    1. Main glued beams (project);
    2. The ventilation membrane overlap;
    3. The ventilation membrane overlap;
    4. Insulation "Roсwool" 100 mm; density of 35-40;
    5. OSB 15 mm;
    6. The bar 40 x 40 mm;
    7. Finishing floor - decking 40 mm;
    8. Option: laminated plate PSL 60-200 mm.
    9. Option: silent ceiling
     
    6. The EXTERIOR WALLS of the 2nd floor
    1. The simulator logs;
    2. Windscreen vent;
    3. Glued frame;
    4. Insulation "Roсwool" 200 mm; density of 35-40
    5. Vapor barrier channel for networking;
    6. Interior finish simulator timber - 50% of the internal surfaces or GCR.
     
    7. ROOFING
    1. Truss legs (option: PSL beams-plate);
    2. Glued ridged, secondary beams, based on the characteristics of the project;
    3. Insulation "Roсwool" 200 mm (optional 300 mm); density 35;
    4. The vapor barrier (membrane);
    5. Windscreen (membrane);
    6. Bar change of direction (Board sheathing finished ceiling);
    7. Board finishing gypsum Board or ceiling;
    8. Crate (Board for the organization of the air gap of the roof);
    9. Planed counter lathing with prorezheniye technical conditions of roofing tiles (Board to install tile roofing (except shingles) and the side ventilation of the roof.
     
    8. CEILINGS
    Finishing ceilings - ceiling Board 18 mm (spruce, pine) or GCR.
     
    9. WOODEN WINDOWS from glued beams, the German technology
    Windows are rectangular with double seal, aluminium drip cap, door thickness 82 mm, painting in a single color on the color ha Miu (painting system "SIKKENS"), glass (36 mm) - M1 double chamber glass thickness.4 mm, opening Windows - tilt and turn (1-fold for the opening), accessories "ROTO NT".
    Windows oblique, round, stained-glass area of more than 3M. square, arched and Windows are less than 1 m2 - oplachivaetsya is a difficulty.
    Bars, rastekanie sash-bars, mosquito nets, coloured in two colors,shutters, blinds, armored and colored glass are extra.
     
    10. DOORS
    The interior is paneled from solid knotty pine, clear lacquer, manufacture Finland or Russia. Leaf height up to 2000 mm., width of 600-900 mm., the Furniture production in Finland.
    Front door (1 piece) - insulated, painted with the "SIKKENS" system, the glass - on request.
     
    11. MOLDED PRODUCTS
    Baseboard, fillet, trim, window sills, layout, overhangs, windshields, windshield, cornice boards, sills, block, Board terrace, terrace fence, slab, terrace garden design, design of roof, beams, rafters, and any other individual wooden elements related to the concept of a wooden house, unconstructive in addition to decorative beams, wood carving, figure connecting.
     
    12. STAIRS
    Ladder made of pine (knots allowed) on the string with a turn at 90º or 180º, platform, or winder treads (according to architecture), lifting height more than 3M, width of steps between 750-1000 mm, without podstupenej, with fencing on the inner side, the wall of the opening steps, finish - clear lacquer, work on ladders to install. Section details:
    1) the string (thickness 45 mm, width - calculation)
    2) level (thickness 45mm, width not over 300 mm)
    3) area (thickness 45mm, width not exceeding 900 mm)
    4) handrails (thickness 45 mm, height 80 mm)
    5) supporting pillars of staircases, pillars, fences (78х78 mm)
    6) baluster rectangular (35х30 mm)
    7) fence opening (length 1000 mm 1.5 column)
    Paid in addition: Replacement of the string to the stringer, stair risers, finishing of end stage birch panel, stairs from the valuable breeds of wood,tinted, invitations (radial) steps, handrails (fences) on the outer side of the staircase,replacement of balusters,the railing of the second light and install it.
     
    13. ANTISEPTIC OF WALL MATERIAL
    The base layer of antiseptic (Finland);
     
    14. COMPONENTS
    All the fixings are metal products (nails, clips, bolts, hangers, straps, plates, etc.), except the metal beams
     
 

 

 
 
 
Akma
Bonvio
KSM
Osnovnoy-postavshchik
Petrovich
Sosnovskiy-DOZ
TBM
Top-Haus
Unikma
Buazeri
 
 
Top
Designed By Kurtasov G.G.